Search found 1475 matches

by ledzep_06
Wed May 04, 2016 9:25 am
Forum: Non-Jeep tech
Topic: Goodyear MTR/k opinions
Replies: 13
Views: 12691

Re: Goodyear MTR/k opinions

I doubt you have an issue with that. My DC Crushers were looking like id only get 20-25k out of them and the mtrs are wearing much slower
by ledzep_06
Wed May 04, 2016 8:52 am
Forum: Non-Jeep tech
Topic: Goodyear MTR/k opinions
Replies: 13
Views: 12691

Re: Goodyear MTR/k opinions

JD i can measure mine on the JK this evening. They were about 19/32 - 20/32 when i put them on last august and its still driven daily. Id say it gets around 10k miles put on it annually
by ledzep_06
Tue Mar 29, 2016 9:00 pm
Forum: Technical Jeep Talk
Topic: P-Metric vs LT
Replies: 24
Views: 17823

Re: P-Metric vs LT

they don't flex as much when you air them down.
Air down farther, they will flex.
by ledzep_06
Tue Mar 29, 2016 8:55 pm
Forum: Technical Jeep Talk
Topic: Front Axle U joint
Replies: 8
Views: 9362

Re: Front Axle U joint

Hammer, screwdriver, ol crappy socket, block of wood or a vise. Everything a man needs to change a u joint. I have two sets of JK D30 axle shafts id love to get sold. One set needs ujoints, the other set is ready to install
by ledzep_06
Mon Mar 28, 2016 1:08 pm
Forum: Technical Jeep Talk
Topic: Chromoly axle shafts
Replies: 14
Views: 12738

Re: Chromoly axle shafts

Im running G2 shafts in my front 44 on the JK. They came with spicer joints and full circle clips. Im not a throttle junky and likely would take awhile before i ever messed up a stock shaft, but i have no complaints.
by ledzep_06
Sun Mar 27, 2016 7:57 am
Forum: Technical Jeep Talk
Topic: Hi-Tuck Exhausts
Replies: 10
Views: 10288

Re: Hi-Tuck Exhausts

Depending on what muffler you run, it may not be necessary to relocate the evap canister. Im running a generic magnaflow from advanced auto right in between the evap canister and frame. Had the local muffler shop run a tail pipe that dumps just in front of the rear bumper. Theres about an inch of cl...
by ledzep_06
Thu Mar 17, 2016 6:20 am
Forum: Technical Jeep Talk
Topic: Loose Steering
Replies: 5
Views: 7590

Re: Loose Steering

Very possibly.
by ledzep_06
Wed Mar 16, 2016 9:31 pm
Forum: Technical Jeep Talk
Topic: Loose Steering
Replies: 5
Views: 7590

Re: Loose Steering

More than likely the toe was knocked out out of spec. Your basically guaranteed to bump the tie rod on something before youd ever hit anything else that would effect alignment. All the trackbar does is center the front axle under the frame. The ABS kicking in will likely be caused by the steering wh...
by ledzep_06
Thu Feb 11, 2016 4:47 pm
Forum: Technical Jeep Talk
Topic: Selectable locker in JK Dana 30
Replies: 25
Views: 18627

Re: Selectable locker in JK Dana 30

You cant do an auto locker in the REAR of a 12+ JK, at least not until the factory transmission software is cracked. The front you can lunch box away. If your going selectable id suggest an OX. no air lines to leak, no internal o rings to leak, no drilling into your housing, no need to buy an on boa...
by ledzep_06
Sat Dec 19, 2015 2:51 pm
Forum: Technical Jeep Talk
Topic: JK Front Driveshatf
Replies: 13
Views: 4912

Re: JK Front Driveshatf

In still running the stockers. Ive broken one front driveshaft but im pretty sure it was a freak ordeal. Twisted close to 400 degrees before it broke
by ledzep_06
Thu Dec 17, 2015 6:36 pm
Forum: Build Threads
Topic: the life of a Samurai...
Replies: 136
Views: 71560

Re: the life of a Samurai...

Keg cell, always cool
by ledzep_06
Wed Dec 09, 2015 1:26 pm
Forum: Technical Jeep Talk
Topic: it's the little things....
Replies: 11
Views: 3860

Re: it's the little things....

everytime I think about how much money ive blown on 4x4 stuff over the years... a baby kitten dies.
by ledzep_06
Tue Dec 08, 2015 4:57 pm
Forum: Technical Jeep Talk
Topic: Rubi axles
Replies: 19
Views: 17691

Re: Rubi axles

If you can get it all for $1k then get it. Just a selectable locker for your current rear 44 will run you a $1k
by ledzep_06
Tue Dec 08, 2015 4:50 pm
Forum: Technical Jeep Talk
Topic: Rubi axles
Replies: 19
Views: 17691

Re: Rubi axles

The rear pinion flange (at least on non rubis) is a cup style for the cv on the driveshaft, the front is a flat flange with 4 bolts so you cant swap them. You got a good deal at $1k. Use the rubi rear axle, but gear/locker for the front, throw a truss on it and rock it.
by ledzep_06
Tue Dec 08, 2015 12:43 pm
Forum: Technical Jeep Talk
Topic: Rubi axles
Replies: 19
Views: 17691

Re: Rubi axles

Theres no pinion flange in the front axle going by the pics. so id say the front is just the housing/shafts. Youd need a ring/pinion and carrier/locker to be ready to roll. Still not a bad deal. You can reuse your D30 knuckles, just make sure the tubes on the front axle arent bent. The Cs look gusse...